- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: Unable to communicate with the RILOE-II/ilo
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-12-2005 05:21 PM
тАО07-12-2005 05:21 PM
Unable to communicate with the RILOE-II/ilo
Unable to communicate with the RILOE-II/ilo.
Any idea what is causing this? Do we have to reboot machines to see card again? Both are in high volume 24/7 trasnactional environments.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-12-2005 11:51 PM
тАО07-12-2005 11:51 PM
Re: Unable to communicate with the RILOE-II/ilo
You could manually restart the drivers (My Computer/Properties/device mangler or control panel)
You may also be able to do this from the systems management home page.
Can you PING the RILOE boards over the network? This will indicate that the network is up and running and that you should be able to talk to the boards from the host.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2005 04:50 AM
тАО07-13-2005 04:50 AM
Re: Unable to communicate with the RILOE-II/ilo
Went to System/Device Manager as suggested. Did not see any method to restart the cards from the driver page, so disabled, then renabled. The message when trying to run hponcfg.exe now is:
ERROR: Couldn't Open the iLo/RILOE-II Driver system file. There is a probem with the ... Drivers installed on this system or ... is disabled ... or device not present.
ACTION REQUIRED: Please Enable iLo/RILOE-II or install ... Drivers.
Cannot ping the board because was trying to access them in HPONCFG to initially set them up with network configuration remotely.
Would like to get them going without a restart.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2005 02:25 PM
тАО07-13-2005 02:25 PM
Re: Unable to communicate with the RILOE-II/ilo
Try this.
In Device manager, uninstall HP Remote Insight Lights-out II Board driver and HP Remote Insight Lights-out II PCI Device driver. Now scan for hardware changes and wait for the the system to automatically install the drivers. If the drivers are not automatically installed, install the drivers manually.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2005 08:25 PM
тАО07-13-2005 08:25 PM
Re: Unable to communicate with the RILOE-II/ilo
In Device manager,
* Disable both HP Remote Insight Lights-out II Board and HP Remote Insight Lights-out II PCI Device
* Enable both of the devices.
Now try to run HPONCFG.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2005 02:19 PM
тАО07-14-2005 02:19 PM
Re: Unable to communicate with the RILOE-II/ilo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2005 02:20 PM
тАО07-14-2005 02:20 PM
Re: Unable to communicate with the RILOE-II/ilo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2005 03:29 PM
тАО07-15-2005 03:29 PM
Re: Unable to communicate with the RILOE-II/ilo
(BTW, decided to restart the server in an attempt to restore communication with the cards as a preference to uninstalling the items, and the restart of the machine did not restore service to the cards.)
So everytime hponcfg sends a script that requires the RILOE-II board to be restarted, both items need to be uninstalled and reinstalled. A hard restart of the machine is not sufficient. Defintely a problem here. This occured on both of our identical DL380 G2 with RILOE-II cards. Workable, but a little time consuming.
Thanks for the suggestion that solved the problem.