No status bars in "VM Host Performance"

[ITSCAC]

Using ICE 6.1
VM Host Xen 5.0/5.5/5.6
In Tab "VM Performance" no status bars show and indicate that "There are no Virtual Machines available on this host", although virtual machine exist on host.
That is it problem?

[sam_193]

did you register your host in HPSIM?

[ITSCAC]

Yes i have.
Host have status "The VM Host is licensed and HP VMM can connect to the VM Host".
See attachment.

[sam_193]

ok, I can see the status despite I dont have VM's running.

Do this as an options:-

1- Rerun the host identification from Option menu-> Identification
2- Rerun VMM regstration from Managed System Setup Wizard ( you can find this inside Configure menu)

Note:- I have attached my screenshot.

[ITSCAC]

It don't help me.
Manage Communications Xen Host in Events is red cross.
Advise SIM says "The HP SIM Central Management Server may not be on the managed system(s)' SNMP trap destination list, so no events will be received from the system(s)." Quick repair don't help. May be it is problem of VW Perfomance&
Can you show right SNMP config for XEN?
See attachment file.

[sam_193]

check in here,/etc/snmp/snmpd.conf . before you make any changes just take a backup of this file so that you wont be in trouble later. post the result.

[ITSCAC]

# Following entries were added by HP Insight Management Agents at
# Wed Jul 28 14:59:25 MSD 2010
dlmod cmaX /usr/lib/libcmaX.so
rwcommunity privat 127.0.0.1
rocommunity public 127.0.0.1
rwcommunity hpserver 10.1.1.205
rocommunity hpserver 10.1.1.205
trapcommunity public
trapcommunity hprepair
trapsink 10.1.1.205 hprepair
syscontact Root (edit /etc/snmp/snmpd.conf)
syslocation Unknown (edit /etc/snmp/snmpd.conf)

# ---------------------- END --------------------
###############################################################################
# Access Control
###############################################################################

# As shipped, the snmpd demon will only respond to queries on the
# system mib group until this file is replaced or modified for
# security purposes.

####
# First, map the community name "public" into a "security name"

# sec.name source community
com2sec notConfigUser default public

####
# Second, map the security name into a group name:

# groupName securityModel securityName
group notConfigGroup v1 notConfigUser
group notConfigGroup v2c notConfigUser

####
# Third, create a view for us to let the group have rights to:

# name incl/excl subtree mask(optional)
view systemview included system
view systemview included interfaces
view systemview included at
view systemview included ip
view systemview included icmp
view systemview included tcp
view systemview included udp
view systemview included snmp

####
# XenServer control domain does not support IPv6.
#
view systemview excluded ipv6InterfaceTableLastChange
view systemview excluded icmpStatsInErrors.ipv6
view systemview excluded icmpStatsInMsgs.ipv6
view systemview excluded icmpStatsOutErrors.ipv6
view systemview excluded icmpStatsOutMsgs.ipv6
view systemview excluded icmpMsgStatsInPkts.ipv6
view systemview excluded icmpMsgStatsOutPkts.ipv6

####
# Finally, grant the group read-only access to the systemview view.

# group context sec.model sec.level prefix read write notif
access notConfigGroup "" any noauth exact systemview none none


###############################################################################
# System contact information
#

[sam_193]

did you try again?

[ITSCAC]

Yes i try, but it still no bars and Events communication in error status.
Attach screenshot.

[sam_193]

run configure and repair agents to fix the SNMP issue. For status baar, do restart of agnts or if possible do aa reboot of VM host and rund identiification in HPSIM