- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Backup Exec 11d does not find MSL6030
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2007 07:49 PM
тАО05-02-2007 07:49 PM
Re: Backup Exec 11d does not find MSL6030
to change the identifier from CPQ to HP you have to make an Firmware Upgrade.
- Uli
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2007 08:51 PM
тАО05-02-2007 08:51 PM
Re: Backup Exec 11d does not find MSL6030
Was this unit purchased as a Compaq library, or HP ? - most MSL6000's were HP, so has the controller module been replaced, or some settings modified ?.
There is a low-level utility called MSLutil.
If I remember correctly, there is an option in that utility to set the identity to Overland, Compaq, or HP. It runs on a Windows box, and uses a serial connection into the library controller. Its available as a download here:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=1849286&prodTypeId=12169&prodSeriesId=316040&swLang=8&taskId=135&swEnvOID=1005#930
However - there isn't much documentation, its not that intuative to use, and you need a special RJ11>D-type cable to use it (this should have been shipped with the library).
It may be worthwhile logging a hardware call with HP, if you're not confident using this utility.
Rich
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2007 08:54 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2007 10:44 PM
тАО05-02-2007 10:44 PM
Re: Backup Exec 11d does not find MSL6030
-Miika
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2007 01:41 AM
тАО05-03-2007 01:41 AM
Re: Backup Exec 11d does not find MSL6030
Thanks to everyone!
-Miika
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2007 01:59 AM
тАО05-03-2007 01:59 AM
Re: Backup Exec 11d does not find MSL6030
can't believe you're the first to go thru that particular "loop"
Rich
- « Previous
- Next »