- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Telnet problem on hpux 11.0
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2004 07:55 PM
03-31-2004 07:55 PM
Telnet problem on hpux 11.0
I have 712 workstation running 11.0. This m/c was running very slow and it used to work normally for sometime after reboot. I checked up on the console of the m/c and found that m/c is not able to ping beyond it's default gateway. On the other hand i was able to telnet to this m/c from my host which is on different subnet but it was very slow.
So i reconfigured the network settings using "set_parms initial". Now system is able to ping beyond it's gateway and also seems to be stable. But some times when i do telnet to this m/c it hangs without giving login prompt, if i open another telnet session to the same m/c it prompts for login with out any problem.
What could be wrong??
Regards
Praveen R
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2004 08:12 PM
03-31-2004 08:12 PM
Re: Telnet problem on hpux 11.0
Seems there is a mismatch of Duplex settings of your network card and the switch where it is connected.
Please check the duplex setting at the switch side of the Lan.(or ask your networking guy to check it)
And then check the Card's Duplex setting i.e. FULL or HALF Duplex.
In HP it seems to be a problem with autonegotiation make it OFF and set the Duplex to the same as the switch.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2004 08:12 PM
03-31-2004 08:12 PM
Re: Telnet problem on hpux 11.0
Do you have a high load on this "small"-system?
It can be that sometimes your system can not allocate enough resource or is out of processes?
Just some thoughts,
Peter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2004 08:35 PM
03-31-2004 08:35 PM
Re: Telnet problem on hpux 11.0
could u execute
#insf -e
from console and try again
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2004 09:13 PM
03-31-2004 09:13 PM
Re: Telnet problem on hpux 11.0
Please ensure that you don't have a duplicate IP-address.
Also you can check /etc/nsswitch.conf file. If you don't use NIS and DNS and these entries are mentioned in the file, you can have big delay in network responce.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2004 06:50 PM
04-01-2004 06:50 PM
Re: Telnet problem on hpux 11.0
It looks like many people have faced this problem, following are few threds which i found intresting:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=139490
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=142349
What does insf -e do??
Regards
Praveen R
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2004 09:47 PM
04-01-2004 09:47 PM
Re: Telnet problem on hpux 11.0
reinstalls device files
check the man pages of insf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2004 09:54 PM
04-01-2004 09:54 PM
Re: Telnet problem on hpux 11.0
As manikandan told, man insf for more details
With best wishes
Naveej
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2004 10:11 PM
04-01-2004 10:11 PM
Re: Telnet problem on hpux 11.0
Any IP address conflict , check with
netfmt -t 50 -f /var/adm/nettl.LOG00